A
-
Aboonajmi, Mohammad
Gearbox fault diagnosis using acoustic data by cepstrum method [Volume 9, Issue 10, 2022, Pages 1-10]
-
Afsari, Ahmad
Investigating the Effect of the Number of Passes and Tool Design in the Friction-Stirring Process on the Grain Size, Hardness and Wear Resistance of Ck45 Steel [Volume 9, Issue 7, 2022, Pages 29-38]
-
Afshari, Davood
Experimental and numerical study on failure of friction stir welded AA6061-T6 joint in conventional and bobbin tool under tensile-shear test using GTN model [Volume 9, Issue 3, 2022, Pages 46-55]
-
Afshari, Mehran
Development of an Integer Linear Programming for Automatic Layout Design in Blanking and Piercing Progressive Dies [Volume 9, Issue 8, 2022, Pages 12-25]
-
Ahmadi, Hamed
Experimental and numerical analysis of the effect of using perforated plates in front of the target against ballistic impact [Volume 9, Issue 7, 2022, Pages 9-21]
-
Ahmadi, Mobina
Synthesis and characterization of porous organic polymers based on diamine and trialdehyde for electrochemical energy storage [Volume 9, Issue 10, 2022, Pages 55-61]
-
Ahmadi Khatir, Farzad
Investigation of process parameters of the hydrodynamic deep drawing assisted by radial pressure using Taguchi and finite element methods [Volume 9, Issue 10, 2022, Pages 11-20]
-
Akbari, Davood
Application of lock-in shearography in non-destructive testing of planar defects [Volume 9, Issue 1, 2022, Pages 1-9]
-
Akbari, Davood
Nondestructive measurement of residual stress in welded steel parts using digital image correlation method [Volume 9, Issue 3, 2022, Pages 18-28]
-
Akbari, Mostafa
Improving the wear and microstructural properties of piston alloys using ZrO2 reinforcing particles [Volume 9, Issue 2, 2022, Pages 52-59]
-
Akhoundi, Behnam
The study of forming of steel cups using hydrodynamic deep drawing process [Volume 9, Issue 8, 2022, Pages 56-64]
-
Akhoundi, Behnam
Investigation of process parameters of the hydrodynamic deep drawing assisted by radial pressure using Taguchi and finite element methods [Volume 9, Issue 10, 2022, Pages 11-20]
-
Akhoundi, Behnam
Using the artificial bee colony optimization, crow, and genetic algorithm for identifying and optimizing the dynamic parameters of a haptic device and operator’s hand [Volume 9, Issue 11, 2023, Pages 21-34]
-
Akhoundi, Behnam
Minimizing the required forming force in the sheet hydroforming process using a fractional factorial design [Volume 9, Issue 12, 2023, Pages 1-9]
-
Almasi, Ali
Comparison of the effect of heat treatment quenching - partitioning (Q-P) and direct quenching (D-Q) on the microstructure and mechanical properties of a high strength steel containing Ti microalloy [Volume 9, Issue 7, 2022, Pages 22-28]
-
Arezoo, Behrooz
Development of an Integer Linear Programming for Automatic Layout Design in Blanking and Piercing Progressive Dies [Volume 9, Issue 8, 2022, Pages 12-25]
-
Asadi, Parviz
Improving the wear and microstructural properties of piston alloys using ZrO2 reinforcing particles [Volume 9, Issue 2, 2022, Pages 52-59]
-
Asadinezhad, Ahmad
Synthesis and characterization of porous organic polymers based on diamine and trialdehyde for electrochemical energy storage [Volume 9, Issue 10, 2022, Pages 55-61]
-
Askari, Mohammad
The assessment of energy absorption capability of aluminum/epoxy-glass fibers laminates after exposer to the thermal cycling [Volume 9, Issue 2, 2022, Pages 30-40]
-
Azimi Aghghaleh, mohamad
Study of hardness and impact resistance in Friction Stir Welding process with Bobbin tool in Aluminum 6061-T6 alloy [Volume 9, Issue 1, 2022, Pages 10-18]
B
-
Bagheri-Bami, Alireza
Determination of the type of anisotropy and stiffness tensor in additive manufacturing polymer components by using ultrasonic waves [Volume 9, Issue 6, 2022, Pages 36-48]
-
Bahramkia, Alireza
Investigating the stability of motorized unilateral external bone fixators to recover the destroyed bones in dynamic mode using the finite element simulation [Volume 9, Issue 4, 2022, Pages 24-35]
-
Bani Mostafa Arab, Nasrolah
Study of hardness and impact resistance in Friction Stir Welding process with Bobbin tool in Aluminum 6061-T6 alloy [Volume 9, Issue 1, 2022, Pages 10-18]
-
Banooei, Hamidreza
Experimental investigating the effect of heat input on the strength of dissimilar welded joints of IN 713LC and AISI 4140 by electron beam welding method [Volume 9, Issue 9, 2022, Pages 45-54]
-
Barazandeh, Reza
The effect of bonding time on microstructure and mechanical properties of Nimonic105 super alloy brazed joint [Volume 9, Issue 6, 2022, Pages 24-35]
-
Bayat, Mohammadreza
Effect of multiple laser shock peening on mechanical properties of aluminum alloy 2014-T6 [Volume 9, Issue 11, 2023, Pages 45-53]
-
Behgozin, Seyed Ahmad
Investigating the Effect of the Number of Passes and Tool Design in the Friction-Stirring Process on the Grain Size, Hardness and Wear Resistance of Ck45 Steel [Volume 9, Issue 7, 2022, Pages 29-38]
-
Behzadnasab, Morteza
Investigating the mechanical behavior of the infinity structure inspired by the silkworm cocoon and comparing it with the rod structure for use in architectural cellular structures [Volume 9, Issue 6, 2022, Pages 11-23]
-
Belbasi, Majid
The effect of bonding time on microstructure and mechanical properties of Nimonic105 super alloy brazed joint [Volume 9, Issue 6, 2022, Pages 24-35]
-
Belbasi, Majid
Investigating Hot Deformation Behavior and Shape Memory Properties of Ni50Ti40Hf10 High Temperature Shape Memory Alloy [Volume 9, Issue 6, 2022, Pages 49-58]
C
-
Cheraghzadeh, Mohammad
Numerical simulation and of gas turbine nozzle baffle manufacturing by hydroforming method [Volume 9, Issue 10, 2022, Pages 28-41]
D
-
Dadgar Asl, Yaghoub
Minimizing the required forming force in the sheet hydroforming process using a fractional factorial design [Volume 9, Issue 12, 2023, Pages 1-9]
-
DadgarAsl, Yaghoub
Numerical and experimental investigation of the effect of local heating on the reduction of the spring back defect in the flexible roll forming process [Volume 9, Issue 9, 2022, Pages 35-44]
-
Davar, Ali
Experimental study of single L-shaped adhesive joints between aluminum and carbon nanographene reinforced composite plate under tensile loading [Volume 9, Issue 4, 2022, Pages 47-60]
-
Deilami Azodi, Hamed
The influence of the amount of CaCO3 foaming agent on the physical structure and mechanical properties of LM13 aluminum foam [Volume 9, Issue 5, 2022, Pages 33-39]
E
-
Ebrahimi, Faezeh
Dynamic behavior of single-layer graphene sheets subjected to a moving mass by using a nonlocal elasticity model and a molecular dynamics simulation [Volume 9, Issue 7, 2022, Pages 39-48]
-
Ebrahimi, Hadi
The experimental and numerical study of the effect die parameters, grain size and ratio t/d on spring-back in micro W-bending [Volume 9, Issue 9, 2022, Pages 1-9]
-
Ebrahimnezhad-Khaljiri, Hossein
Investigating the healing-mechanical behavior of glass fibers/epoxy self-healing composites containing microcapsules and silica nanoparticles under the shear loading [Volume 9, Issue 1, 2022, Pages 31-42]
-
Eghbali, Beitallah
Investigation of formability of commercially pure titanium in equal channel angular pressing process [Volume 9, Issue 7, 2022, Pages 49-63]
-
Eivazi Bagheri, Hadi
Study of nonconductive Si3N4 ceramic machining ability by electrical discharge machining process by assisting electrode [Volume 9, Issue 5, 2022, Pages 13-22]
-
Eivazi Bagheri, Hadi
Design and manufacturing of three layer pressure vessel by Shrink fit process [Volume 9, Issue 12, 2023, Pages 10-18]
-
Elahi, Seyed Hossein
The influence of the amount of CaCO3 foaming agent on the physical structure and mechanical properties of LM13 aluminum foam [Volume 9, Issue 5, 2022, Pages 33-39]
-
Elyasi, Majid
Investigating the microstructure variation of commercially pure titanium in hot resistance spinning [Volume 9, Issue 4, 2022, Pages 36-46]
-
Elyasi, Majid
Experimental study of two-point incremental forming of St12 sheet using negative dies [Volume 9, Issue 12, 2023, Pages 32-42]
-
Entezarian, Mohammad Mahdi
Experimental and numerical study on failure of friction stir welded AA6061-T6 joint in conventional and bobbin tool under tensile-shear test using GTN model [Volume 9, Issue 3, 2022, Pages 46-55]
-
Eskandari Jam, Jafar
Experimental study of single L-shaped adhesive joints between aluminum and carbon nanographene reinforced composite plate under tensile loading [Volume 9, Issue 4, 2022, Pages 47-60]
-
Eslami Farsani, Reza
The assessment of energy absorption capability of aluminum/epoxy-glass fibers laminates after exposer to the thermal cycling [Volume 9, Issue 2, 2022, Pages 30-40]
-
Eslami-Farsani, Reza
Investigating the healing-mechanical behavior of glass fibers/epoxy self-healing composites containing microcapsules and silica nanoparticles under the shear loading [Volume 9, Issue 1, 2022, Pages 31-42]
-
Esmaeilian, Mojtaba
Experimental and theoretical investigation of a tilting pad journal bearing for application in high-speed turbine aero engines [Volume 9, Issue 5, 2022, Pages 23-32]
-
Etemadi Haghighi, Shahram
Mathematical and experimental modeling of plasma channel radius in alternating magnetic field assisted electric discharge machining process [Volume 9, Issue 11, 2023, Pages 54-65]
F
-
Fadaei, Hasan
The effect of bonding time on microstructure and mechanical properties of Nimonic105 super alloy brazed joint [Volume 9, Issue 6, 2022, Pages 24-35]
-
Fakhraie, Mehran
Investigating the stability of motorized unilateral external bone fixators to recover the destroyed bones in dynamic mode using the finite element simulation [Volume 9, Issue 4, 2022, Pages 24-35]
-
Fallah, Mohammad Meghdad
Analytical investigation of influence of rotational speed and feed rate on temperature elevation in jawbone drilling [Volume 9, Issue 1, 2022, Pages 54-62]
-
Fallah, Mohammad Meghdad
Experimental study of residual stress in parts with variable cross section in selective laser melting process [Volume 9, Issue 2, 2022, Pages 8-17]
-
Farahani, Mohammadreza
Experimental and numerical investigation of the vibration stress relief process on a T- shape welded joint [Volume 9, Issue 1, 2022, Pages 43-53]
-
Farahani, Mohammadreza
Experimental investigating the effect of heat input on the strength of dissimilar welded joints of IN 713LC and AISI 4140 by electron beam welding method [Volume 9, Issue 9, 2022, Pages 45-54]
-
Farhang, Majid
Experimental and numerical investigation of the vibration stress relief process on a T- shape welded joint [Volume 9, Issue 1, 2022, Pages 43-53]
-
Farrokhabadi, Amin
Optimizing the failure analysis of a network structure using artificial neural network and genetic algorithm [Volume 9, Issue 11, 2023, Pages 35-44]
-
Fartashvand, Vahid
Suspension and trapping particles with a positive contrast factor and investigating the effect of particle volume in a liquid medium by the acoustophoretic phenomenon [Volume 9, Issue 4, 2022, Pages 12-23]
-
Fathollahi Dehkordi, Siavash
Design, modeling and motion simulation of robotic manipulators with time-varying structure in a fluid environment [Volume 9, Issue 2, 2022, Pages 41-51]
-
Fayazi Khanigi, Alireza
Effect of multiple laser shock peening on mechanical properties of aluminum alloy 2014-T6 [Volume 9, Issue 11, 2023, Pages 45-53]
G
-
Geranmayeh, Abdolreza
The assessment of energy absorption capability of aluminum/epoxy-glass fibers laminates after exposer to the thermal cycling [Volume 9, Issue 2, 2022, Pages 30-40]
-
Ghafari, Mohsen
Investigating the microstructure variation of commercially pure titanium in hot resistance spinning [Volume 9, Issue 4, 2022, Pages 36-46]
-
Ghanadi, Noushin
Optimizing the failure analysis of a network structure using artificial neural network and genetic algorithm [Volume 9, Issue 11, 2023, Pages 35-44]
-
Ghasemi Tamami, Peyman
Nondestructive measurement of residual stress in welded steel parts using digital image correlation method [Volume 9, Issue 3, 2022, Pages 18-28]
-
Ghazvini, Mohsen
Suspension and trapping particles with a positive contrast factor and investigating the effect of particle volume in a liquid medium by the acoustophoretic phenomenon [Volume 9, Issue 4, 2022, Pages 12-23]
-
Ghermezi, Masoud
Effect of multiple laser shock peening on mechanical properties of aluminum alloy 2014-T6 [Volume 9, Issue 11, 2023, Pages 45-53]
-
Gholami, Raheb
Investigating the stability of motorized unilateral external bone fixators to recover the destroyed bones in dynamic mode using the finite element simulation [Volume 9, Issue 4, 2022, Pages 24-35]
-
Ghorbani, Hadi
Investigating and comparing the mechanical properties of ABS/GF continuous fiber composite and ABS polymer produced by fused deposition modeling method [Volume 9, Issue 9, 2022, Pages 26-34]
-
Ghorbani, Masumeh
Design and construction of advanced sorting inorder to chromite segregation [Volume 9, Issue 3, 2022, Pages 11-17]
-
Golzar, Mohammad
Investigating and comparing the mechanical properties of ABS/GF continuous fiber composite and ABS polymer produced by fused deposition modeling method [Volume 9, Issue 9, 2022, Pages 26-34]
H
-
Habibi, Zahra
Comparison of the effect of heat treatment quenching - partitioning (Q-P) and direct quenching (D-Q) on the microstructure and mechanical properties of a high strength steel containing Ti microalloy [Volume 9, Issue 7, 2022, Pages 22-28]
-
Hadad, Mohammadjafar
Experimental Investigation on Micro Friction Stir Welding of Al-Cu [Volume 9, Issue 2, 2022, Pages 18-29]
-
Hajfathalian, Alireza
Experimental study of two-point incremental forming of St12 sheet using negative dies [Volume 9, Issue 12, 2023, Pages 32-42]
-
Hajiveiseh, Mona
Buckling and bending analysis of functional porous plate using shear deformation theory [Volume 9, Issue 8, 2022, Pages 34-43]
-
Hajizadeh, kaveh
Investigation of formability of commercially pure titanium in equal channel angular pressing process [Volume 9, Issue 7, 2022, Pages 49-63]
-
Hasanabadi, Ali
Investigating the energy absorption quality of the porous Schwarz P structure made by 3D printing method [Volume 9, Issue 11, 2023, Pages 13-20]
-
Hashemi, Bita
Analysis of circular fiber metal laminate plates with curvilinear fiber under low velocity impact loading [Volume 9, Issue 4, 2022, Pages 61-71]
-
Hashemi, Seyyed Hojjat
Comparison of experimental and numerical correction factors from seam weld fracture energy by drop weight tear testing of gas transportation pipelines [Volume 9, Issue 3, 2022, Pages 29-37]
-
Hassan Beygi, Sayed Reza
Gearbox fault diagnosis using acoustic data by cepstrum method [Volume 9, Issue 10, 2022, Pages 1-10]
-
HassanPour, Peyman
Experimental Analysis and Optimization of Thrust Force in the Orthopedic Drilling Process Using the Tool Coated with Titanium Nitride Nano Coating by the Physical Vapor Deposition Method [Volume 9, Issue 5, 2022, Pages 49-59]
-
Hedayatnejad, Rasoull
Effect of laser power variation in AM-LMD process on Inconel 718 powder deposition profile on Inconel 738 [Volume 9, Issue 4, 2022, Pages 1-11]
-
Heydari Beni, Mohsen
Experimental study of single L-shaped adhesive joints between aluminum and carbon nanographene reinforced composite plate under tensile loading [Volume 9, Issue 4, 2022, Pages 47-60]
-
Hojjat, Yousef
Suspension and trapping particles with a positive contrast factor and investigating the effect of particle volume in a liquid medium by the acoustophoretic phenomenon [Volume 9, Issue 4, 2022, Pages 12-23]
-
Honarvar, Farhang
Determination of the type of anisotropy and stiffness tensor in additive manufacturing polymer components by using ultrasonic waves [Volume 9, Issue 6, 2022, Pages 36-48]
-
Hosseini, Shahram
Optimizing the failure analysis of a network structure using artificial neural network and genetic algorithm [Volume 9, Issue 11, 2023, Pages 35-44]
-
Hosseini Vajari, Mostafa
Investigating the mechanical behavior of the infinity structure inspired by the silkworm cocoon and comparing it with the rod structure for use in architectural cellular structures [Volume 9, Issue 6, 2022, Pages 11-23]
-
Hosseinpour, Mahdi
Investigation of dynamic absorber parameters to improve the vibration behavior of boring bar [Volume 9, Issue 7, 2022, Pages 1-8]
I
-
Imanian, Emad
Using the artificial bee colony optimization, crow, and genetic algorithm for identifying and optimizing the dynamic parameters of a haptic device and operator’s hand [Volume 9, Issue 11, 2023, Pages 21-34]
J
-
Jafarzadegan, Mostafa
The effect of bonding time on microstructure and mechanical properties of Nimonic105 super alloy brazed joint [Volume 9, Issue 6, 2022, Pages 24-35]
-
Janghorban, Maziar
Investigating the Effect of the Number of Passes and Tool Design in the Friction-Stirring Process on the Grain Size, Hardness and Wear Resistance of Ck45 Steel [Volume 9, Issue 7, 2022, Pages 29-38]
-
Javadi, Mehrdad
The assessment of energy absorption capability of aluminum/epoxy-glass fibers laminates after exposer to the thermal cycling [Volume 9, Issue 2, 2022, Pages 30-40]
-
Joudaki, Jalal
Comparison of Tensile Strength for 3D Printed Parts Fabricated by Fused Filament Fabrication (FFF) [Volume 9, Issue 5, 2022, Pages 40-48]
K
-
Karafi, Mohammad Reza
Design and fabrication of six axis force/torque sensor using strain gauges [Volume 9, Issue 3, 2022, Pages 1-10]
-
Karimi Ivanaki, Mohammad
Experimental and numerical study on failure of friction stir welded AA6061-T6 joint in conventional and bobbin tool under tensile-shear test using GTN model [Volume 9, Issue 3, 2022, Pages 46-55]
-
Kashfi, Mohammad
Analysis of circular fiber metal laminate plates with curvilinear fiber under low velocity impact loading [Volume 9, Issue 4, 2022, Pages 61-71]
-
Kazerooni, Afshin
Experimental study of residual stress in parts with variable cross section in selective laser melting process [Volume 9, Issue 2, 2022, Pages 8-17]
-
Khajehpoor, Salar
Investigating the stability of motorized unilateral external bone fixators to recover the destroyed bones in dynamic mode using the finite element simulation [Volume 9, Issue 4, 2022, Pages 24-35]
-
Khorsand, Hamid
Fabrication and characterization of FeCoNiCuCr nano structured high entropy alloy using wet mechanical alloying [Volume 9, Issue 6, 2022, Pages 1-10]
-
Khozestani, Alireza
Suspension and trapping particles with a positive contrast factor and investigating the effect of particle volume in a liquid medium by the acoustophoretic phenomenon [Volume 9, Issue 4, 2022, Pages 12-23]
-
Kian Vash, Abbas
Comparison of the effect of heat treatment quenching - partitioning (Q-P) and direct quenching (D-Q) on the microstructure and mechanical properties of a high strength steel containing Ti microalloy [Volume 9, Issue 7, 2022, Pages 22-28]
-
Kolagar, Ali Mohammad
Additive manufacturing of nickel-based superalloy gas turbine components [Volume 9, Issue 3, 2022, Pages 38-45]
-
Kolagar, Ali Mohammad
Numerical simulation and of gas turbine nozzle baffle manufacturing by hydroforming method [Volume 9, Issue 10, 2022, Pages 28-41]
L
-
Liaghat, Gholamhosein
Experimental and numerical analysis of the effect of using perforated plates in front of the target against ballistic impact [Volume 9, Issue 7, 2022, Pages 9-21]
-
Liaghat, Gholamhossein
Investigating the bending properties of polymeric orthopedic plaque made of different polymers by additive manufacturing method [Volume 9, Issue 9, 2022, Pages 21-25]
M
-
Mahdian, Asghar
Experimental and theoretical investigation of a tilting pad journal bearing for application in high-speed turbine aero engines [Volume 9, Issue 5, 2022, Pages 23-32]
-
Mahdianikhotbesara, Ali
Experimental Investigation on Micro Friction Stir Welding of Al-Cu [Volume 9, Issue 2, 2022, Pages 18-29]
-
Mahmoudi-Meymand, Mahdi
Damage detection on the graphene sheet due to impact loading [Volume 9, Issue 8, 2022, Pages 26-33]
-
Majidi Jirandehi, Ali Akbar
Dynamic behavior of single-layer graphene sheets subjected to a moving mass by using a nonlocal elasticity model and a molecular dynamics simulation [Volume 9, Issue 7, 2022, Pages 39-48]
-
Majidi-Jirandehi, Ali Akbar
Comparison of experimental and numerical correction factors from seam weld fracture energy by drop weight tear testing of gas transportation pipelines [Volume 9, Issue 3, 2022, Pages 29-37]
-
Majidi-Jirandehi, Ali Akbar
Damage detection on the graphene sheet due to impact loading [Volume 9, Issue 8, 2022, Pages 26-33]
-
Manouchehri, Amir Mohammad
Investigating and comparing the mechanical properties of ABS/GF continuous fiber composite and ABS polymer produced by fused deposition modeling method [Volume 9, Issue 9, 2022, Pages 26-34]
-
Mansouri, Elahe
Fabrication and characterization of FeCoNiCuCr nano structured high entropy alloy using wet mechanical alloying [Volume 9, Issue 6, 2022, Pages 1-10]
-
Mansouri, Morteza
Experimental study of residual stress in parts with variable cross section in selective laser melting process [Volume 9, Issue 2, 2022, Pages 8-17]
-
Marzban, Mohammad Javad
Investigating the Effect of the Number of Passes and Tool Design in the Friction-Stirring Process on the Grain Size, Hardness and Wear Resistance of Ck45 Steel [Volume 9, Issue 7, 2022, Pages 29-38]
-
Mashayekhi, Ahmad
The study of forming of steel cups using hydrodynamic deep drawing process [Volume 9, Issue 8, 2022, Pages 56-64]
-
Mashayekhi, Ahmad
Investigation of process parameters of the hydrodynamic deep drawing assisted by radial pressure using Taguchi and finite element methods [Volume 9, Issue 10, 2022, Pages 11-20]
-
Mashayekhi, Ahmad
Using the artificial bee colony optimization, crow, and genetic algorithm for identifying and optimizing the dynamic parameters of a haptic device and operator’s hand [Volume 9, Issue 11, 2023, Pages 21-34]
-
Masoudi, Ali
Investigating and comparing the mechanical properties of ABS/GF continuous fiber composite and ABS polymer produced by fused deposition modeling method [Volume 9, Issue 9, 2022, Pages 26-34]
-
Mesroghli, Shahin
Design and construction of advanced sorting inorder to chromite segregation [Volume 9, Issue 3, 2022, Pages 11-17]
-
Mirafzali, Seyyed Mohammad Bagher
Investigating the energy absorption quality of the porous Schwarz P structure made by 3D printing method [Volume 9, Issue 11, 2023, Pages 13-20]
-
Mirhosseini, Seyed Farzad
Experimental study of single L-shaped adhesive joints between aluminum and carbon nanographene reinforced composite plate under tensile loading [Volume 9, Issue 4, 2022, Pages 47-60]
-
Mirnia, Mohammad Javad
Investigating the microstructure variation of commercially pure titanium in hot resistance spinning [Volume 9, Issue 4, 2022, Pages 36-46]
-
Mirnia, Mohammad Javad
Numerical simulation and of gas turbine nozzle baffle manufacturing by hydroforming method [Volume 9, Issue 10, 2022, Pages 28-41]
-
Mirnia, Mohammad Javad
Experimental study of two-point incremental forming of St12 sheet using negative dies [Volume 9, Issue 12, 2023, Pages 32-42]
-
Mirzamohammadi, Sadegh
Investigating the healing-mechanical behavior of glass fibers/epoxy self-healing composites containing microcapsules and silica nanoparticles under the shear loading [Volume 9, Issue 1, 2022, Pages 31-42]
-
Moayedi Manizani, Siavash
Experimental investigation of mechanical and microscopic properties of ABS-Ni composite made by Fused Deposition Modeling (FDM) method [Volume 9, Issue 9, 2022, Pages 10-20]
-
Modanloo, Vahid
The study of forming of steel cups using hydrodynamic deep drawing process [Volume 9, Issue 8, 2022, Pages 56-64]
-
Modanloo, Vahid
Investigation of process parameters of the hydrodynamic deep drawing assisted by radial pressure using Taguchi and finite element methods [Volume 9, Issue 10, 2022, Pages 11-20]
-
Modanloo, Vahid
Using the artificial bee colony optimization, crow, and genetic algorithm for identifying and optimizing the dynamic parameters of a haptic device and operator’s hand [Volume 9, Issue 11, 2023, Pages 21-34]
-
Modanloo, Vahid
Minimizing the required forming force in the sheet hydroforming process using a fractional factorial design [Volume 9, Issue 12, 2023, Pages 1-9]
-
Mofid, Mohammad Ammar
The effect of bonding time on microstructure and mechanical properties of Nimonic105 super alloy brazed joint [Volume 9, Issue 6, 2022, Pages 24-35]
-
Mohamadi, Masoud
Analytical investigation of influence of rotational speed and feed rate on temperature elevation in jawbone drilling [Volume 9, Issue 1, 2022, Pages 54-62]
-
Mohammadi, Naser
Development an advanced neural network for recognition of machining feature [Volume 9, Issue 5, 2022, Pages 1-12]
-
Moradi Nasab, Hossein
Investigating the mechanical behavior of the infinity structure inspired by the silkworm cocoon and comparing it with the rod structure for use in architectural cellular structures [Volume 9, Issue 6, 2022, Pages 11-23]
-
Mousavi, Seyyed Mohammad Vahab
Design and manufacturing of three layer pressure vessel by Shrink fit process [Volume 9, Issue 12, 2023, Pages 10-18]
-
Mozaffari, Mohammad Hossein
Investigation the effect of mechanical properties of materials in solving the inverse identification problem by means of optimization algorithms [Volume 9, Issue 11, 2023, Pages 1-12]
N
-
Naghavi Alhoseini, Seyed Amirhosein
Comparison of Tensile Strength for 3D Printed Parts Fabricated by Fused Filament Fabrication (FFF) [Volume 9, Issue 5, 2022, Pages 40-48]
-
Nakhaei, Mohammad Reza
Investigation of mechanical, thermal and microstructural properties of PA6/NBR nanocomposites reinforced with silicon carbide nanoparticles [Volume 9, Issue 10, 2022, Pages 42-54]
-
Naseroleslami, Amir
Design and manufacturing of three layer pressure vessel by Shrink fit process [Volume 9, Issue 12, 2023, Pages 10-18]
-
Nasimi, Leyli
Comparison of the effect of heat treatment quenching - partitioning (Q-P) and direct quenching (D-Q) on the microstructure and mechanical properties of a high strength steel containing Ti microalloy [Volume 9, Issue 7, 2022, Pages 22-28]
-
Nategh, Mohammad Javad
Development an advanced neural network for recognition of machining feature [Volume 9, Issue 5, 2022, Pages 1-12]
-
Nikkhah Shahmirzadi, Mahmoud
Investigating the mechanical behavior of the infinity structure inspired by the silkworm cocoon and comparing it with the rod structure for use in architectural cellular structures [Volume 9, Issue 6, 2022, Pages 11-23]
-
Nikzare, Javad
Experimental and numerical analysis of the effect of using perforated plates in front of the target against ballistic impact [Volume 9, Issue 7, 2022, Pages 9-21]
P
-
Pak, Abbas
Experimental Analysis and Optimization of Thrust Force in the Orthopedic Drilling Process Using the Tool Coated with Titanium Nitride Nano Coating by the Physical Vapor Deposition Method [Volume 9, Issue 5, 2022, Pages 49-59]
-
Pak, Abbas
Design, modeling and manufacturing a novel continues ultrasonic cleaning tank by harmonic response analysis [Volume 9, Issue 10, 2022, Pages 21-27]
-
Panahizadeh, Valiollah
Numerical and experimental investigation of the effect of local heating on the reduction of the spring back defect in the flexible roll forming process [Volume 9, Issue 9, 2022, Pages 35-44]
-
Parvizi, Soroush
Study of hardness and impact resistance in Friction Stir Welding process with Bobbin tool in Aluminum 6061-T6 alloy [Volume 9, Issue 1, 2022, Pages 10-18]
-
Podinehei, Rahele
The experimental and numerical study of the effect die parameters, grain size and ratio t/d on spring-back in micro W-bending [Volume 9, Issue 9, 2022, Pages 1-9]
-
Pol, Mohammah Hossein
Investigating the bending properties of polymeric orthopedic plaque made of different polymers by additive manufacturing method [Volume 9, Issue 9, 2022, Pages 21-25]
Q
-
Qasemi, Mahdi
Intelligent modeling of cutting force in bone micromilling process by fuzzy logic [Volume 9, Issue 12, 2023, Pages 54-62]
-
Qasemi, Reza
Intelligent modeling of cutting force in bone micromilling process by fuzzy logic [Volume 9, Issue 12, 2023, Pages 54-62]
R
-
Rabiee, Amir Hossein
Intelligent modeling of cutting force in bone micromilling process by fuzzy logic [Volume 9, Issue 12, 2023, Pages 54-62]
-
Rahi, Abbas
Investigation of dynamic absorber parameters to improve the vibration behavior of boring bar [Volume 9, Issue 7, 2022, Pages 1-8]
-
Rahimi Asiabaraki, Hossein
Improving the wear and microstructural properties of piston alloys using ZrO2 reinforcing particles [Volume 9, Issue 2, 2022, Pages 52-59]
-
Rahmati, Sadegh
Effect of laser power variation in AM-LMD process on Inconel 718 powder deposition profile on Inconel 738 [Volume 9, Issue 4, 2022, Pages 1-11]
-
Raissi, Pouria
Numerical simulation and of gas turbine nozzle baffle manufacturing by hydroforming method [Volume 9, Issue 10, 2022, Pages 28-41]
S
-
Sabbaghi Farshi, Sina
Application of lock-in shearography in non-destructive testing of planar defects [Volume 9, Issue 1, 2022, Pages 1-9]
-
Sabet, Hamed
Effect of laser power variation in AM-LMD process on Inconel 718 powder deposition profile on Inconel 738 [Volume 9, Issue 4, 2022, Pages 1-11]
-
Safarabadi, Amin
Electrical discharge machining of metal matrix composite AZ91 magnesium alloy and investigation and optimization of the effect of input parameters on material removal rate and workpiece surface roughness [Volume 9, Issue 6, 2022, Pages 59-69]
-
Safarabadi Farahani, Majid
Experimental and numerical investigation of the vibration stress relief process on a T- shape welded joint [Volume 9, Issue 1, 2022, Pages 43-53]
-
Safari, Mehdi
Numerical investigation of deformation behavior in laser bending of sheet with curved irradiating scheme [Volume 9, Issue 2, 2022, Pages 1-7]
-
Salamat-talab, Mazaher
Investigating the behavior of axial force and temperature in the drilling process of glass/epoxy composites with and without curvature [Volume 9, Issue 12, 2023, Pages 19-31]
-
Salehi, Mohammad
Experimental investigation of mechanical and microscopic properties of ABS-Ni composite made by Fused Deposition Modeling (FDM) method [Volume 9, Issue 9, 2022, Pages 10-20]
-
Salemi Golezani, Ali
Effect of laser power variation in AM-LMD process on Inconel 718 powder deposition profile on Inconel 738 [Volume 9, Issue 4, 2022, Pages 1-11]
-
Seifoori, Sajjad
Comparison of experimental and numerical correction factors from seam weld fracture energy by drop weight tear testing of gas transportation pipelines [Volume 9, Issue 3, 2022, Pages 29-37]
-
Seifoori, Sajjad
Dynamic behavior of single-layer graphene sheets subjected to a moving mass by using a nonlocal elasticity model and a molecular dynamics simulation [Volume 9, Issue 7, 2022, Pages 39-48]
-
Seifoori, Sajjad
Damage detection on the graphene sheet due to impact loading [Volume 9, Issue 8, 2022, Pages 26-33]
-
Seyyed Afghahi, Salman
Design and manufacturing of three layer pressure vessel by Shrink fit process [Volume 9, Issue 12, 2023, Pages 10-18]
-
Seyyed Afghahi, Seyyed Salman
Study of nonconductive Si3N4 ceramic machining ability by electrical discharge machining process by assisting electrode [Volume 9, Issue 5, 2022, Pages 13-22]
-
Shafinejad Bejandi, Amin
Effect of multiple laser shock peening on mechanical properties of aluminum alloy 2014-T6 [Volume 9, Issue 11, 2023, Pages 45-53]
-
Shahfaragh, Pouria
Experimental and numerical investigation of the vibration stress relief process on a T- shape welded joint [Volume 9, Issue 1, 2022, Pages 43-53]
-
Shahidi, Alireza
Design, modeling and manufacturing a novel continues ultrasonic cleaning tank by harmonic response analysis [Volume 9, Issue 10, 2022, Pages 21-27]
-
Shahraki, Saeid
The experimental and numerical study of the effect die parameters, grain size and ratio t/d on spring-back in micro W-bending [Volume 9, Issue 9, 2022, Pages 1-9]
-
Shahriari, Behrooz
Experimental and theoretical investigation of a tilting pad journal bearing for application in high-speed turbine aero engines [Volume 9, Issue 5, 2022, Pages 23-32]
-
Shakouri, Ehsan
Analytical investigation of influence of rotational speed and feed rate on temperature elevation in jawbone drilling [Volume 9, Issue 1, 2022, Pages 54-62]
-
Shamshiri, Mehdi
Numerical and experimental investigation of the effect of local heating on the reduction of the spring back defect in the flexible roll forming process [Volume 9, Issue 9, 2022, Pages 35-44]
-
Sheikhi, Mohammadmorad
Analytical investigation of influence of rotational speed and feed rate on temperature elevation in jawbone drilling [Volume 9, Issue 1, 2022, Pages 54-62]
-
Sheykhi, Mohammadreza
Experimental and theoretical investigation of a tilting pad journal bearing for application in high-speed turbine aero engines [Volume 9, Issue 5, 2022, Pages 23-32]
-
Shirin Abadi Farahani, Ali
Design, modeling and manufacturing a novel continues ultrasonic cleaning tank by harmonic response analysis [Volume 9, Issue 10, 2022, Pages 21-27]
-
Shirzadi, Mahmood
Mathematical and experimental modeling of plasma channel radius in alternating magnetic field assisted electric discharge machining process [Volume 9, Issue 11, 2023, Pages 54-65]
-
Soleimanimehr, Hamid
Mathematical and experimental modeling of plasma channel radius in alternating magnetic field assisted electric discharge machining process [Volume 9, Issue 11, 2023, Pages 54-65]
-
Soleymani, Farshad
Study of nonconductive Si3N4 ceramic machining ability by electrical discharge machining process by assisting electrode [Volume 9, Issue 5, 2022, Pages 13-22]
-
Soleymani, Hadi
Investigation of mechanical, thermal and microstructural properties of PA6/NBR nanocomposites reinforced with silicon carbide nanoparticles [Volume 9, Issue 10, 2022, Pages 42-54]
-
Soltani, Majid
Investigating the mechanical behavior of the infinity structure inspired by the silkworm cocoon and comparing it with the rod structure for use in architectural cellular structures [Volume 9, Issue 6, 2022, Pages 11-23]
-
Soltani, Sadegh
The influence of the amount of CaCO3 foaming agent on the physical structure and mechanical properties of LM13 aluminum foam [Volume 9, Issue 5, 2022, Pages 33-39]
-
Sousanabadi Farahani, Amin
Electrical discharge machining of metal matrix composite AZ91 magnesium alloy and investigation and optimization of the effect of input parameters on material removal rate and workpiece surface roughness [Volume 9, Issue 6, 2022, Pages 59-69]
T
-
Tahami, Seyed Mohammad
Investigating the stability of motorized unilateral external bone fixators to recover the destroyed bones in dynamic mode using the finite element simulation [Volume 9, Issue 4, 2022, Pages 24-35]
-
Taheri, Arman
Investigating the behavior of axial force and temperature in the drilling process of glass/epoxy composites with and without curvature [Volume 9, Issue 12, 2023, Pages 19-31]
-
Taheri, Moein
Investigation of different geometry of gold nanoparticles in the displacement of the second phase of three-dimensional manipulation using an AFM [Volume 9, Issue 8, 2022, Pages 1-11]
-
Taherzadehghahfarokh, Mohammad Reza
Design and fabrication of six axis force/torque sensor using strain gauges [Volume 9, Issue 3, 2022, Pages 1-10]
-
Tahmasbi, Vahid
Experimental Analysis and Optimization of Thrust Force in the Orthopedic Drilling Process Using the Tool Coated with Titanium Nitride Nano Coating by the Physical Vapor Deposition Method [Volume 9, Issue 5, 2022, Pages 49-59]
-
Tahmasbi, Vahid
Electrical discharge machining of metal matrix composite AZ91 magnesium alloy and investigation and optimization of the effect of input parameters on material removal rate and workpiece surface roughness [Volume 9, Issue 6, 2022, Pages 59-69]
-
Tahmasbi, Vahid
Investigating the behavior of axial force and temperature in the drilling process of glass/epoxy composites with and without curvature [Volume 9, Issue 12, 2023, Pages 19-31]
-
Tahmasbi, Vahid
Intelligent modeling of cutting force in bone micromilling process by fuzzy logic [Volume 9, Issue 12, 2023, Pages 54-62]
-
Talebian, Soheil
Experimental and theoretical study on effects of magnetic field and mechanical stress on structural coefficients and magnetomechanical behavior of terfenol-D [Volume 9, Issue 1, 2022, Pages 19-30]
-
Talebi-Ghadikolaee, Hossein
The study of forming of steel cups using hydrodynamic deep drawing process [Volume 9, Issue 8, 2022, Pages 56-64]
-
Talebi-Ghadikolaee, Hossein
Investigation of process parameters of the hydrodynamic deep drawing assisted by radial pressure using Taguchi and finite element methods [Volume 9, Issue 10, 2022, Pages 11-20]
-
Tanhaie, Fahimeh
Determining the order of products entering the mixed-model assembly line using the exact methods [Volume 9, Issue 8, 2022, Pages 44-55]
-
Teimouri, Behzad
Experimental and numerical analysis of parameters affecting the mechanical behavior of closed cell aluminum foam in low-speed impact [Volume 9, Issue 12, 2023, Pages 43-53]
-
Tutunchi, Abolfazl
Comparison of the effect of heat treatment quenching - partitioning (Q-P) and direct quenching (D-Q) on the microstructure and mechanical properties of a high strength steel containing Ti microalloy [Volume 9, Issue 7, 2022, Pages 22-28]
Y
-
Yarmohammad Tooski, Mehdi
Experimental study of single L-shaped adhesive joints between aluminum and carbon nanographene reinforced composite plate under tensile loading [Volume 9, Issue 4, 2022, Pages 47-60]
-
Yazdani, Mojtaba
Experimental and numerical analysis of parameters affecting the mechanical behavior of closed cell aluminum foam in low-speed impact [Volume 9, Issue 12, 2023, Pages 43-53]
Z
-
Zamani, Mahdi
Gearbox fault diagnosis using acoustic data by cepstrum method [Volume 9, Issue 10, 2022, Pages 1-10]
-
Zamani, Zahra
Analysis of circular fiber metal laminate plates with curvilinear fiber under low velocity impact loading [Volume 9, Issue 4, 2022, Pages 61-71]
-
Zamani Ashani, Jamal
Experimental investigation of mechanical and microscopic properties of ABS-Ni composite made by Fused Deposition Modeling (FDM) method [Volume 9, Issue 9, 2022, Pages 10-20]
-
Zare Mehrjardi, Mehdi
Investigation the effect of mechanical properties of materials in solving the inverse identification problem by means of optimization algorithms [Volume 9, Issue 11, 2023, Pages 1-12]
-
Zeinolabedin Beygi, Ali
Experimental Analysis and Optimization of Thrust Force in the Orthopedic Drilling Process Using the Tool Coated with Titanium Nitride Nano Coating by the Physical Vapor Deposition Method [Volume 9, Issue 5, 2022, Pages 49-59]
-
Zeinolabedin Beygi, Ali
The study of forming of steel cups using hydrodynamic deep drawing process [Volume 9, Issue 8, 2022, Pages 56-64]
-
Zeinolabedin Beygi, Ali
Investigation of process parameters of the hydrodynamic deep drawing assisted by radial pressure using Taguchi and finite element methods [Volume 9, Issue 10, 2022, Pages 11-20]
-
Zolfaghari, Mojtaba
Electrical discharge machining of metal matrix composite AZ91 magnesium alloy and investigation and optimization of the effect of input parameters on material removal rate and workpiece surface roughness [Volume 9, Issue 6, 2022, Pages 59-69]
Your query does not match with any item